Equipment and handling

Pallet jacks: manual vs electric

Updated · 5 sources

A manual pallet jack is pumped and pulled by hand; an electric one drives and lifts with electric motors. Crown, for example, rates its PTH 50 manual jack at up to 5,000 lb (about 2,268 kg) and its walkie and rider electric jacks at up to 3,300 to 8,000 lb (about 1,497 to 3,629 kg) [4]. Powered jacks fall under OSHA's powered industrial truck rule, training included [1][2].

How manual and electric jacks work

A manual (hand) pallet jack has two forks, load wheels near the fork tips, and a long handle that both steers the truck and works the hydraulic pump. Pumping the handle raises the forks until the pallet clears the floor, and a control lever on the handle lowers them again. On Crown's PTH series, for example, a neutral lever position releases tension on the handle for easier maneuvering, and articulated 7 in (about 178 mm) steer wheels are designed for dock plates, trailers and uneven floors [5].

An electric (powered) pallet jack does the same work with electric motors, so the operator controls travel and lift from the handle instead of pulling the load and pumping. Walkie models are controlled by an operator walking with the truck, and rider models carry the operator on the truck. Crown's line, for example, includes walkie, end-control walkie rider, center-control rider and rider pallet trucks [4]. OSHA's forklift eTool lists low-lift walkie pallet trucks and low-lift walkie/rider pallet trucks among its Class III examples, the class for electric motor hand trucks and hand/rider trucks [2].

What capacity to look for

Rated capacity appears on the spec sheet and, on powered trucks, on capacity plates or decals [1]. OSHA expects each operator to know the truck specifications on the nameplate and what they mean [2], and its rule allows only loads within the truck's rated capacity to be handled [1]. The table shows one manufacturer's published line-up as an example of the range, not a recommendation.

Type Crown series Listed capacity
Manual pallet jack PTH 50 Up to 5,000 lb (about 2,268 kg)
Manual high-lift (scissor) jack PTH 50 S Up to 2,200 lb (about 998 kg)
Compact electric pallet jack WJ Up to 3,300 lb (about 1,497 kg)
Electric walkie pallet jack WP Up to 4,500 lb (about 2,041 kg)
Heavy-duty electric pallet jack PW Up to 8,000 lb (about 3,629 kg)
End-control walkie rider PE Up to 8,000 lb (about 3,629 kg)
Rider and center-control rider RT, PR, PC Up to 4,500 to 8,000 lb (about 2,041 to 3,629 kg)

Capacities are from Crown's pallet truck pages [4][5]; kilograms are converted at 0.4536 kg per lb and rounded. The jack lifts the pallet as well as the goods, and the pallet has limits of its own, covered in pallet load capacity.

Match the forks to your pallets

Two fork dimensions decide whether a jack suits your pallets: fork length, and overall width, which is the outside spread across both forks. Crown offers its PTH 50 with forks from 36 to 72 in long (about 914 to 1,829 mm) and overall widths from 15.8 to 27 in (about 401 to 686 mm) [5].

  • Length. Forks shorter than the pallet leave its far end unsupported, and longer forks stick out the other side, where they can catch whatever is behind it. Match the length to the side you push into: on a 48 x 40 in pallet entered from a 40 in end, the forks run along the 48 in side. The pallet sizes chart lists other footprints.
  • Width. The overall width has to fit the pallet's openings. If yours are narrow, check a narrower model; Crown's PTH range starts at 15.8 in [5].
  • Entry. Which sides a jack can go into depends on how the pallet is built, and stringer vs block pallets explains the difference.
  • Skids. Crown sells a skid adapter that raises fork height so the PTH can handle skids [5].

Operator training: what OSHA requires

OSHA's powered industrial truck standard, 29 CFR 1910.178, covers fork trucks, tractors, platform lift trucks, motorized hand trucks and other specialized industrial trucks powered by electric motors or internal combustion engines [1]. In a 2023 interpretation letter, OSHA applied the standard to electric carts designed to carry, push or pull material, quoting the ANSI B56.1-1969 definition of a powered industrial truck as a "mobile, power-driven vehicle used to carry, push, pull, lift, stack, or tier material" [3]. Its forklift eTool lists low-lift walkie pallet trucks as Class III powered industrial trucks [2]. A jack that is pumped and pulled by hand has neither of the power sources the standard's scope names [1].

For powered trucks, paragraph 1910.178(l) sets out operator training [1]:

  • The employer must ensure each operator is competent, as shown by completing the required training and evaluation, before the operator runs the truck other than for training.
  • Trainees may operate a truck only under the direct supervision of people with the knowledge, training and experience to train and evaluate operators, and only where doing so doesn't endanger them or other employees.
  • Training combines formal instruction, practical training, and an evaluation of the operator's performance in the workplace.
  • Topics cover the truck, such as controls, steering, capacity, stability and battery charging, and the workplace, such as floor surfaces, loads, pedestrian traffic, narrow aisles and ramps.
  • Refresher training is required after unsafe operation, an accident or near miss, an evaluation showing unsafe operation, assignment to a different type of truck, or a workplace change that affects safe operation. Each operator's performance must be evaluated at least once every three years.
  • The employer certifies the training, recording the operator's name, the training and evaluation dates, and who trained or evaluated the operator.

The same section requires powered trucks to be examined before being placed in service, at least daily, or after each shift where they run around the clock. A truck found unsafe must be taken out of service until it is repaired, and motorized hand trucks must enter elevators and other confined areas load end forward [1].

Manual or electric: how to choose

Neither type is better in general; it depends on the work.

  • Effort and distance. With a manual jack, the operator pumps to lift and pushes or pulls the whole load. An electric jack takes over both, which counts for more as loads get heavier and runs get longer.
  • Ramps and docks. For powered trucks, OSHA requires loaded trucks to be driven with the load upgrade on grades over 10 percent, and dockboards to be secured before they are driven over and never loaded past their rated capacity [1].
  • Charging. Battery charging areas need ventilation for fumes from gassing batteries, and smoking is prohibited there [1].
  • Lift height. Standard jacks lift a pallet just clear of the floor; Crown's PTH 50 S scissor model raises its forks up to 31.3 in (about 795 mm) for use as a work positioner [5].

Buying vs pallet jack rental

Prices aren't listed here, because they vary by model, dealer and region. These questions usually decide it:

  • How long and how often. Weigh how long you need it against how often it will run.
  • Upkeep. For powered trucks, OSHA requires repairs by authorized personnel, using replacement parts equivalent in safety to the originals [1].
  • Training. Renting doesn't change the training paragraph, which is written as a duty of the employer whose employees operate the truck [1].
  • Warranty. If you buy, compare warranty and service terms. Crown offers extended warranty coverage of up to five years on the PTH [5].
  • Rental. Crown's PTH page links to the company's rental inventory [5]; ask whether the model you need is in it.

Need pallets or have some to move? Use the pallet request form.

Sources

  1. 29 CFR 1910.178 Powered industrial trucks, eCFR (Office of the Federal Register). Accessed November 19, 2026.
  2. Powered Industrial Trucks (Forklift) eTool: Forklift Classifications, Occupational Safety and Health Administration (Internet Archive copy). Accessed November 19, 2026.
  3. Powered Industrial Trucks (standard interpretation letter, September 19, 2023), Occupational Safety and Health Administration (Internet Archive copy). Accessed November 19, 2026.
  4. Manual and Electric Pallet Jacks, Crown Equipment. Accessed November 19, 2026.
  5. PTH Series Manual Pallet Jack, Crown Equipment. Accessed November 19, 2026.