Standards and safety
Heat-treated pallets and the ISPM 15 mark
ISPM 15 is the international standard for wood packaging, pallets included, that moves between countries. A pallet that meets it carries a boxed mark with the IPPC symbol, a two-letter country code, a producer or treatment provider code, and a treatment code: HT for heat treatment, DH for dielectric heating, MB for methyl bromide or SF for sulphuryl fluoride [1].
What ISPM 15 covers
ISPM 15 is one of the International Standards for Phytosanitary Measures adopted under the International Plant Protection Convention (IPPC). Its aim is to reduce the spread of quarantine pests, mainly pests of living trees, in wood packaging made from raw wood. It covers crates, boxes, packing cases, dunnage, pallets, cable drums and spools [1].
Some wood packaging is exempt because the standard treats it as low risk [1]:
- packaging made entirely of wood 6 mm (about 1/4 in) thick or less
- packaging made wholly of processed wood such as plywood, particle board, oriented strand board or veneer
- sawdust, wood shavings and wood wool
- wood components permanently attached to freight vehicles and containers
US import rules follow the standard. Wood packaging used to support, protect or carry cargo into the United States must be treated and certified under ISPM 15, while plastic pallets, plywood, pressboard and oriented strand board are not subject to APHIS regulation [2]. If you are weighing materials, see plastic vs wood pallets.
The four treatment codes
| Code | Treatment | What the standard requires |
|---|---|---|
| HT | Heat treatment in a conventional steam or dry kiln chamber | At least 56 °C (132.8 °F) for at least 30 continuous minutes through the whole profile of the wood, core included |
| DH | Dielectric heating (microwave or radio frequency) | At least 60 °C (140 °F) for 1 continuous minute through the whole profile, surface included |
| MB | Methyl bromide fumigation | At least 24 hours, with the wood and air no colder than 10 °C (50 °F), reaching a set concentration-time dose; not allowed if any piece is over 20 cm (about 7.9 in) at its smallest cross-section |
| SF | Sulphuryl fluoride fumigation | Wood at least 20 °C (68 °F); 24 hours at 30 °C (86 °F) or above, or 48 hours at 20 °C or above; not allowed for pieces over 20 cm or wood above 75% moisture content (dry basis) |
All four rows come from Annex 1 of the standard [1]. For methyl bromide, the required dose rises as the temperature drops, from a concentration-time product of 650 g·h/m³ at 21 °C or above to 900 g·h/m³ at 10 to 15.9 °C [1]. The standard also says methyl bromide depletes the ozone layer and encourages national plant protection organisations to promote the alternative treatments [1].
Two rules apply whatever the treatment:
- Debarking. Wood packaging must be made of debarked wood. Small, separate pieces of bark may remain if each is under 3 cm (about 1.2 in) wide or, if wider, under 50 cm² (about 7.8 sq in) in area [1].
- Kiln-drying is not automatically HT. Kiln-drying, steam heating, heat-enabled chemical pressure impregnation and dielectric heating can all count as heat treatment, but only when they meet the heat treatment requirements [1].
Letters such as KD or DB are not among the four treatment codes, and the standard says no other information may sit inside the mark's border; extra marks, such as a producer's trademark, go outside it [1]. For what those extra letters mean when you reuse a pallet, see pallet wood safety.
How to read the stamp
The standard requires four parts, with the symbol on the left [1]:
- Symbol. The IPPC symbol, which must closely resemble the official design.
- Country code. The two-letter ISO country code, joined by a hyphen to the next part.
- Producer or treatment provider code. A unique code that the country's plant protection organisation assigns to the producer or treatment provider.
- Treatment code. HT, DH, MB or SF, placed after the other codes, either on its own line or separated by a hyphen.
The mark must be square or rectangular, inside a border, with a vertical line separating the symbol from the codes. It must be legible, durable and not transferable, it must not be hand drawn, and it should preferably appear on at least two opposite sides. Red and orange should be avoided because those colours are used for dangerous goods labels [1]. Older pallets may carry marks made under earlier versions of the standard, which the standard says countries should accept at import [1].
On US-made pallets the mark also shows who certified it. APHIS lists the parts as the accredited agency's trademark (outside the ISPM 15 mark), the facility number, HT or MB, the two-letter country code, the IPPC symbol, and DUN when the wood is dunnage [3].
APHIS treats these as signs of non-compliant packaging: a stamp that is illegible or not on the lumber, a mark with no border or the wrong logo, no stamp at all, and signs of pests such as exit holes, trails, feeding damage and frass, insect waste that looks like sawdust [2].
Who runs the program in the US
The American Lumber Standard Committee (ALSC) manages two quality control programs for wood packaging under an agreement with USDA's Animal and Plant Health Inspection Service (APHIS): one for heat treatment and one for methyl bromide fumigation [3]. Producers enroll with an ALSC-accredited inspection agency, and APHIS says you cannot make your own ISPM 15 mark without being registered with one [3]. ALSC says its program has 15 accredited independent third-party agencies covering about 5,300 facilities, and that it operates under memoranda of understanding with APHIS [4].
Under the heat treatment program, a producer either builds from lumber that already carries an accredited agency's HT mark, or builds the packaging first and heats it to a core temperature of 56 °C for at least 30 minutes [3].
Why the mark matters for export
APHIS keeps a list of countries that have stated in writing that they require ISPM 15-compliant wood packaging. It includes the European Union, the United Kingdom, Canada, Mexico, Japan, Australia and India, and APHIS notes the list is not all-inclusive [3]. Canada and the United States exempt packaging made from wood that originated in the continental United States or Canada, provided the import documents include a statement of that origin [3].
The mark replaces a phytosanitary certificate for the packaging [1], and APHIS does not issue certificates for wood packaging that is carrying a shipment [3]. APHIS also says hardwood packaging must be treated and marked too [3]. At the border, packaging without the mark, or where pests are found, can be detained, treated, destroyed or sent back [1]. For the rest of the export checklist, see how to ship a pallet.
Reuse, repair and remanufacture
A treated and marked pallet that has not been repaired, remanufactured or otherwise altered does not need re-treating or re-marking for the rest of its service life [1]. APHIS puts it as the treatment not expiring [3]. Repairs change that:
- Repaired means up to about one third of the components have been replaced. Replacement wood must itself be treated, with each added piece individually marked, or be processed wood such as plywood. Countries where repairs happen may also require old marks to be removed and the whole unit re-treated [1].
- Remanufactured means more than about one third has been replaced. Old marks must be permanently obliterated, for example by painting over or grinding, and the unit re-treated and marked again [1].
For US exporters, APHIS says repaired or remanufactured packaging must be heat-treated or fumigated again, with the old mark obliterated and a new one applied by an inspection agency [3]. For how recyclers describe repaired and remanufactured pallets, see pallet grades.
One limit is worth knowing. The standard says its measures are not intended to give ongoing protection from pests or other organisms that reach the wood later [1]. A stamp tells you how the wood was treated, not what the pallet has been through since.
Sources
- ISPM 15. Regulation of wood packaging material in international trade, International Plant Protection Convention (IPPC) Secretariat, FAO. Accessed November 19, 2026.
- Wood Packaging Material, USDA Animal and Plant Health Inspection Service (APHIS). Accessed November 19, 2026.
- Export ISPM 15-Compliant Wood Packaging Material From the United States to Another Country, USDA Animal and Plant Health Inspection Service (APHIS). Accessed November 19, 2026.
- Wood Packaging Material Program, American Lumber Standard Committee (ALSC). Accessed November 19, 2026.